If your office chair feels wrong after a few hours of work, the problem usually isn't the chair - it's the setup. A well-adjusted chair distributes load across your hips, supports the natural curve of your lower spine, and lets your forearms rest level with the desk. A poorly-adjusted one quietly funnels that load into your neck, shoulders, and lumbar discs.
This guide walks through the seven adjustments that matter on a modern ergonomic chair, in the order you should dial them in. The targets - feet flat, knees roughly level with hips, elbows at about 90 degrees, lower back fully supported - are drawn from the Canadian Centre for Occupational Health and Safety, the GSA Ergonomic Seating Adjustment Guide, and Cornell University's ergonomics program.
Before you start: find your chair's controls
Most ergonomic chairs hide their controls in three places: under the seat pan, on the underside of the backrest, and along the armrest stems. Before adjusting anything, do a quick inventory.
- Under the seat (front): pneumatic height lever, seat-depth slider, sometimes a forward-tilt knob.
- Under the seat (rear): tilt-tension knob (usually a large round dial), recline lock.
- Backrest: lumbar height/depth adjustment, backrest angle lever.
- Armrests: height button on the stem, pivot/slide controls on the pad.
If your chair came with a manual, skim the diagram. If not, search the model name plus "adjustment guide" - most manufacturers publish one.

Step 1: Set seat height first
Seat height anchors everything else. Get it wrong and every other adjustment compensates around the error.
- Stand in front of the chair. Adjust the height so the highest point of the seat pan sits just below your kneecap - this is the CCOHS-recommended starting point.
- Sit down. Your feet should rest flat on the floor, and your thighs should be roughly parallel to the ground.
- Check the angle at your knees and hips - both should be open to about 90 degrees or slightly more. Knees noticeably higher than hips means the seat is too low; the front of your thighs feeling pinched means it's too high.
If you can't keep your feet flat at the height your desk demands, raise the chair and add a footrest rather than letting your feet dangle.
Step 2: Adjust seat depth (the clenched-fist test)
Not every chair offers seat-depth adjustment, but if yours does, this is the step that fixes mystery thigh pressure and tight hamstrings.
Sit all the way back so your lower back contacts the lumbar curve of the backrest. Then check the gap between the front edge of the seat and the back of your calves.
The CCOHS rule of thumb: that gap should be about the width of a clenched fist - roughly 2 inches or 5 cm. If the seat digs into the back of your knees, slide it back. If you've got more than a fist of space, slide it forward so the seat actually supports your thighs.

Step 3: Dial in lumbar support
Lumbar support is a small mechanism with an outsized effect. Done right, it preserves the natural inward curve of your lower spine; done wrong, it either disappears or jabs you in the kidneys.
- Slide the lumbar pad up or down until its peak sits at the small of your back - usually around belt-line height.
- If your chair offers depth or firmness adjustment, dial it in until you feel gentle, even contact across your lower back rather than a single pressure point.
- Sit upright. The support should let you maintain a relaxed S-curve without you having to actively brace.
If you're feeling more pressure than support, back the depth off a notch. Lumbar support should feel like the chair is meeting you, not pushing you.
Step 4: Set the backrest angle and recline
The old "sit at 90 degrees" advice is out of date. Cornell University's ergonomics research recommends a slight recline - around 110 degrees - for keyboard and mouse work, because it opens up your hip angle and takes load off the lumbar discs.
- For focused desk work, set the backrest between 100 and 110 degrees from the seat.
- If your chair has a recline lock with multiple stops, pick the stop closest to that range and engage it.
- Don't be afraid to unlock the recline periodically and lean back further during reading, calls, or thinking time. Shifting positions throughout the day matters more than picking the perfect single angle.
Step 5: Tune tilt tension
Tilt tension controls how much force the chair takes to recline. The right setting lets you lean back smoothly under your own body weight, and lets the chair return upright without snapping forward.
The tension knob is usually a large round dial at the front-underside of the seat. Heavier users generally need more tension; lighter users, less.
- Too tight: you have to push hard to recline, and the chair feels stiff at every position.
- Too loose: the chair tips backward whenever you lean, and you use your core to pull yourself upright.
Adjust in small increments and test with a few normal lean-backs before locking it in.
Step 6: Position the armrests
Armrests do their job when they support your forearms without forcing your shoulders up or letting them slump. Get the height first, then the width.
- Sit upright with your shoulders relaxed and your arms hanging loosely. Bend your elbows to about 90 degrees.
- Raise or lower the armrests until they barely touch the undersides of your elbows - the CCOHS standard. If the lowest setting still lifts your shoulders, drop the armrests further or remove them entirely.
- If your armrests slide in or out, position them close enough to support your forearms while typing, but not so close they bump your torso.
- If your armrests pivot, angle them slightly inward for mouse work and back to neutral for keyboard work.
A common mistake is letting the armrests carry your weight while you reach for the keyboard. They should support your arms, not act as a brace.
Step 7: Engage the lock (if you want to)
Most ergonomic chairs let you lock the recline at a chosen angle. Whether you should use it is personal - research from Humanics Ergonomics suggests that varying your posture across the day matters more than holding one "perfect" angle.
If you do lock the recline, pick the 100-110 degree range from Step 4 as your default and leave it unlocked during low-focus tasks so the chair can move with you.
A 30-second daily check
Once you've dialled in the full setup, you don't need to start over every morning. A 30-second check is enough.
- Feet flat on the floor (or footrest).
- A fist of space behind your knees.
- Lower back fully supported, no gap between you and the backrest.
- Elbows at about 90 degrees, shoulders relaxed.
- Eyes level with the top third of your monitor (a separate fix - see our monitor positioning guide).
If any of those drift, take 10 seconds to nudge the chair back into spec rather than letting your body compensate.
Common adjustment mistakes
- Setting the chair to fit the desk. A non-adjustable desk should be matched with a higher chair plus a footrest, not a lower chair with dangling feet.
- Cranking lumbar support to maximum. More pressure isn't better - even, gentle contact is the goal.
- Locking the recline at 90 degrees. Cornell's research and Wirecutter's reporting both recommend a slight backward recline for typing work.
- Using armrests as a desk substitute. If your forearms are resting on armrests instead of the desk, the chair is the wrong height for the desk.
- Setting it and forgetting it. Bodies change across a day. The best chair owners adjust two or three settings throughout each workday.
Office chair adjustment FAQ
What is the correct height for an office chair?
Adjust the chair so your feet rest flat on the floor and your thighs are roughly parallel to the ground, with your knees opening to about 90 degrees or slightly more. The CCOHS shortcut: while standing in front of the chair, set the top of the seat pan to just below your kneecap.
Should I sit at 90 degrees or recline slightly?
Cornell University ergonomics research recommends a slight recline of around 100 to 110 degrees for keyboard and mouse work. The reclined angle opens your hip joint and takes load off your lumbar discs compared with strict 90-degree sitting.
How do I know if my lumbar support is set correctly?
The lumbar pad should sit at the small of your back, roughly around belt-line height, and apply gentle even contact rather than pushing into a single spot. If you feel pressure in your kidneys or your back arches away from the chair, reduce the depth or move the pad lower.
Where should the armrests be?
Sit upright with shoulders relaxed and elbows bent to 90 degrees. Raise the armrests until they barely touch the undersides of your elbows. If the lowest setting still lifts your shoulders, lower the armrests further or remove them. Armrests should support your forearms, not bear your body weight.
How can I adjust an office chair without a lever?
A chair with no visible lever usually has a manual screw mechanism under the seat or a fixed-height pneumatic that needs servicing. Check the underside for a threaded post or service label. If the pneumatic cylinder has failed, replacement cylinders fit most standard chairs and are inexpensive.
How often should I readjust my office chair?
Run a 30-second posture check at the start of each work session: feet flat, fist of space behind the knees, lower back supported, elbows at 90 degrees. Make small adjustments two or three times a day as your posture drifts - varying position across the day matters more than holding one ideal angle.
